Enter configuration commands, one per line. End with CNTL/Z.
R-DPS(config)#int fa0/0
R-DPS(config-if)#spe
R-DPS(config-if)#speed 100
R-DPS(config-if)#dup
R-DPS(config-if)#duplex full
R-DPS(config-if)#ba
R-DPS(config-if)#band
R-DPS(config-if)#bandwidth 100.000
^
% Invalid input detected at '^' marker.
R-DPS(config-if)#bandwidth 100000
R-DPS(config-if)#q
^
% Invalid input detected at '^' marker.
R-DPS(config-if)#^Z
R-DPS#sh ru
R-DPS#sh run
R-DPS#sh running-config int fa0/0
Building configuration...
Current configuration : 110 bytes
!
interface FastEthernet0/0
bandwidth 100000
ip address 10.1.3.1 255.255.255.0
speed 100
full-duplex
end
R-DPS#sh int fa0/0
FastEthernet0/0 is up, line protocol is up
Hardware is Gt96k FE, address is c00d.0128.0000 (bia c00d.0128.0000)
Internet address is 10.1.3.1/24
MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA, loopback not set
Keepalive set (10 sec)
Full-duplex, 100Mb/s, 100BaseTX/FX
ARP type: ARPA, ARP Timeout 04:00:00
Last input 00:00:00, output 00:00:00, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue: 0/40 (size/max)
5 minute input rate 1000 bits/sec, 2 packets/sec
5 minute output rate 1000 bits/sec, 2 packets/sec
29399 packets input, 2678701 bytes
Received 4423 broadcasts, 0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
0 watchdog
0 input packets with dribble condition detected
5748 packets output, 465908 bytes, 0 underruns
0 output errors, 0 collisions, 3 interface resets
R-DPS#de
R-DPS#debu
R-DPS#debug ?
IUA ISDN adaptation Layer options
aaa AAA Authentication, Authorization and Accounting
aal2_xgcpspi AAL2_XGCP Service Provider Interface.
access-expression Boolean access expression
acircuit Attachment Circuit information
adjacency adjacency
alarm-interface Alarm Interface Card events
all Enable all debugging
archive debug archive commands
arp IP ARP and HP Probe transactions
asnl Application Subscribe Notify Layer
async Async interface information
backhaul-session-manager Backhaul SM options
backup Backup events
bcm560x BCM560X L2 Driver
beep BEEP debugging
bgp BGP information
bing Bing(d) debugging
call Call Information
call-admission Call admission control
call-mgmt Call Management
callback Callback activity
R-DPS#debug ip os
R-DPS#debug ip ospf
% Incomplete command.
R-DPS#debug ip ospf
% Incomplete command.
R-DPS#debug ip ospf ?
adj OSPF adjacency events
database-timer OSPF database timer
events OSPF events
flood OSPF flooding
hello OSPF hello events
lsa-generation OSPF lsa generation
mpls OSPF MPLS
nsf OSPF non-stop forwarding events
packet OSPF packets
retransmission OSPF retransmission events
spf OSPF spf
tree OSPF database tree
R-DPS#debug ip ospf he
R-DPS#debug ip ospf hello
OSPF hello events debugging is on
R-DPS#no debug ip ospf hello
OSPF hello events debugging is off
R-DPS#no debug ip ospf pac
R-DPS#no debug ip ospf packet
OSPF packet debugging is off
R-DPS#ter
R-DPS#terminal ?
autohangup Automatically hangup when last connection closes
autoselect Set line to autoselect
data-character-bits Size of characters being handled
databits Set number of data bits per character
default Set a command to its defaults
dispatch-character Define the dispatch character
dispatch-timeout Set the dispatch timer
domain-lookup Enable domain lookups in show commands
download Put line into 'download' mode
editing Enable command line editing
escape-character Change the current line's escape character
exec Configure EXEC
exec-character-bits Size of characters to the command exec
flowcontrol Set the flow control
full-help Provide help to unprivileged user
help Description of the interactive help system
history Enable and control the command history function
hold-character Define the hold character
international Enable international 8-bit character support
ip IP options
length Set number of lines on a screen
modem Configure the Modem Control Lines
R-DPS#terminal
% Incomplete command.
R-DPS#terminal mo
R-DPS#terminal mon
R-DPS#terminal monitor
R-DPS#debug ip ospf packet
OSPF packet debugging is on
R-DPS#terminal monitor
R-DPS#
*Mar 1 03:49:04.991: OSPF: rcv. v:2 t:1 l:48 rid:10.100.100.2
aid:0.0.0.0 chk:ED0 aut:0 auk: from Serial0/0
R-DPS#
*Mar 1 03:49:14.963: OSPF: rcv. v:2 t:1 l:48 rid:10.100.100.2
aid:0.0.0.0 chk:ED0 aut:0 auk: from Serial0/0
R-DPS#
*Mar 1 03:49:24.963: OSPF: rcv. v:2 t:1 l:48 rid:10.100.100.2
aid:0.0.0.0 chk:ED0 aut:0 auk: from Serial0/0
R-DPS#
*Mar 1 03:49:34.947: OSPF: rcv. v:2 t:1 l:48 rid:10.100.100.2
aid:0.0.0.0 chk:ED0 aut:0 auk: from Serial0/0
R-DPS#
R-DPS#no debug ip ospf packet
OSPF packet debugging is off
R-DPS#
*Mar 1 03:56:07.851: %OSPF-5-ADJCHG: Process 100, Nbr 10.100.100.2 on Serial0/0 from FULL to DOWN, Neighbor Down: Dead timer expired
R-DPS#conf t
Enter configuration commands, one per line. End with CNTL/Z.
R-DPS(config)#no ro
R-DPS(config)#no router ospf
% Incomplete command.
R-DPS(config)#no router ?
bgp Border Gateway Protocol (BGP)
eigrp Enhanced Interior Gateway Routing Protocol (EIGRP)
isis ISO IS-IS
iso-igrp IGRP for OSI networks
mobile Mobile routes
odr On Demand stub Routes
ospf Open Shortest Path First (OSPF)
rip Routing Information Protocol (RIP)
R-DPS(config)#no router os
R-DPS(config)#no router ospf 100
R-DPS(config)#router ospf 100
R-DPS(config-router)#net 10.1.3.1 0.0.0.0 area 1
R-DPS(config-router)#net
*Mar 1 03:58:51.095: %OSPF-4-ERRRCV: Received invalid packet: mismatch area ID, from backbone area must be virtual-link but not found from 10.1.1.1, FastEthernet0/0
R-DPS(config-router)#net 10.1.3.1 0.0.0.0 area 1
*Mar 1 03:59:01.115: %OSPF-4-ERRRCV: Received invalid packet: mismatch area ID, from backbone area must be virtual-link but not found from 10.1.1.1, FastEthernet0/0
R-DPS(config-router)#
*Mar 1 03:59:11.051: %OSPF-4-ERRRCV: Received invalid packet: mismatch area ID, from backbone area must be virtual-link but not found from 10.1.1.1, FastEthernet0/0
R-DPS(config-router)#no router ospf 100
R-DPS(config)#router ospf 100
R-DPS(config-router)#net 10.100.100.4 0.0.0.0 area 1
R-DPS(config-router)#net 10.1.3.1 0.0.0.0 area 1
R-DPS(config-router)#net 10.1.3.1 0.0.0.0 area 1
*Mar 1 04:00:01.111: %OSPF-4-ERRRCV: Received invalid packet: mismatch area ID, from backbone area must be virtual-link but not found from 10.1.1.1, FastEthernet0/0
R-DPS(config-router)#net 10.1.3.1 0.0.0.0 area 1
*Mar 1 04:00:11.131: %OSPF-4-ERRRCV: Received invalid packet: mismatch area ID, from backbone area must be virtual-link but not found from 10.1.1.1, FastEthernet0/0
R-DPS(config-router)#net 10.1.3.6 0.0.0.0 area 1
*Mar 1 04:00:21.071: %OSPF-4-ERRRCV: Received invalid packet: mismatch area ID, from backbone area must be virtual-link but not found from 10.1.1.1, FastEthernet0/0
R-DPS(config-router)#net 10.1.3.6 0.0.0.0 area 1
R-DPS(config-router)#end
R-DPS#
*Mar 1 04:00:29.611: %SYS-5-CONFIG_I: Configured from console by vty1 (10.1.3.10)
R-DPS#
*Mar 1 04:00:31.087: %OSPF-4-ERRRCV: Received invalid packet: mismatch area ID, from backbone area must be virtual-link but not found from 10.1.1.1, FastEthernet0/0
R-DPS#
*Mar 1 04:00:41.111: %OSPF-4-ERRRCV: Received invalid packet: mismatch area ID, from backbone area must be virtual-link but not found from 10.1.1.1, FastEthernet0/0
R-DPS#
*Mar 1 04:00:51.075: %OSPF-4-ERRRCV: Received invalid packet: mismatch area ID, from backbone area must be virtual-link but not found from 10.1.1.1, FastEthernet0/0
R-DPS#
*Mar 1 04:01:01.091: %OSPF-4-ERRRCV: Received invalid packet: mismatch area ID, from backbone area must be virtual-link but not found from 10.1.1.1, FastEthernet0/0
R-DPS#
*Mar 1 04:01:11.095: %OSPF-4-ERRRCV: Received invalid packet: mismatch area ID, from backbone area must be virtual-link but not found from 10.1.1.1, FastEthernet0/0
R-DPS#
*Mar 1 04:01:21.075: %OSPF-4-ERRRCV: Received invalid packet: mismatch area ID, from backbone area must be virtual-link but not found from 10.1.1.1, FastEthernet0/0
R-DPS#conf t
Enter configuration commands, one per line. End with CNTL/Z.
R-DPS(config)#router ospf 100
R-DPS(config-router)#pas
R-DPS(config-router)#passive-interface
*Mar 1 04:01:31.107: %OSPF-4-ERRRCV: Received invalid packet: mismatch area ID, from backbone area must be virtual-link but not found from 10.1.1.1, FastEthernet0/0
R-DPS(config-router)#passive-interface fa
R-DPS(config-router)#passive-interface fastEthernet 0/0
R-DPS(config-router)#sh ip ospf ne
R-DPS(config-router)#exit
R-DPS(config)#exit
R-DPS#
*Mar 1 04:03:21.786: %SYS-5-CONFIG_I: Configured from console by vty1 (10.1.3.10)
R-DPS#sh ip ospf neigh
R-DPS#sh ip ospf neighbor
R-DPS#sh run | s rouetr
R-DPS#
R-DPS#sh run | s roter
R-DPS#
R-DPS#
R-DPS#sh run | s router
router ospf 100
log-adjacency-changes
passive-interface FastEthernet0/0
network 10.1.3.1 0.0.0.0 area 1
network 10.1.3.6 0.0.0.0 area 1
network 10.100.100.4 0.0.0.0 area 1
R-DPS#conf t
Enter configuration commands, one per line. End with CNTL/Z.
R-DPS(config)#ro
R-DPS(config)#router os
R-DPS(config)#router ospf 100
R-DPS(config-router)#net
R-DPS(config-router)#no network 10.1.3.6 0.0.0.0 area 0
R-DPS(config-router)#network 10.0.0.6 0.0.0.0 area 0
R-DPS(config-router)#end
R-DPS#sh run | s router
*Mar 1 04:05:39.810: %SYS-5-CONFIG_I: Configured from console by vty1 (10.1.3.10)router ospf 100
log-adjacency-changes
passive-interface FastEthernet0/0
network 10.0.0.6 0.0.0.0 area 0
network 10.1.3.1 0.0.0.0 area 1
network 10.1.3.6 0.0.0.0 area 1
network 10.100.100.4 0.0.0.0 area 1
R-DPS#conf t
Enter configuration commands, one per line. End with CNTL/Z.
R-DPS(config)#router ospf 100
R-DPS(config-router)#network 10.0.0.6 0.0.0.0 area 1
R-DPS(config-router)#
*Mar 1 04:06:09.002: %OSPF-6-AREACHG: 10.0.0.6/32 changed from area 0 to area 1
R-DPS(config-router)#
*Mar 1 04:06:09.514: %OSPF-5-ADJCHG: Process 100, Nbr 10.100.100.2 on Serial0/0 from LOADING to FULL, Loading Done
R-DPS(config-router)#no network 10.0.0.6 0.0.0.0 area 0
R-DPS(config-router)#no network 10.1.3.6 0.0.0.0 area 1
R-DPS(config-router)#end
R-DPS#conf t
*Mar 1 04:06:41.402: %SYS-5-CONFIG_I: Configured from console by vty1 (10.1.3.10)
R-DPS#sh run | s router
router ospf 100
log-adjacency-changes
passive-interface FastEthernet0/0
network 10.0.0.6 0.0.0.0 area 1
network 10.1.3.1 0.0.0.0 area 1
network 10.100.100.4 0.0.0.0 area 1
R-DPS#sh ip
R-DPS#sh ip os
R-DPS#sh ip ospf ne
R-DPS#sh ip ospf neighbor
Neighbor ID Pri State Dead Time Address Interface
10.100.100.2 0 FULL/ - 00:00:39 10.0.0.5 Serial0/0
R-DPS#sh ip ro
Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP
D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area
N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2
E1 - OSPF external type 1, E2 - OSPF external type 2
i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2
ia - IS-IS inter area, * - candidate default, U - per-user static route
o - ODR, P - periodic downloaded static route
Gateway of last resort is not set
10.0.0.0/8 is variably subnetted, 20 subnets, 3 masks
O 10.0.0.8/30 [110/96] via 10.0.0.5, 00:02:00, Serial0/0
O IA 10.0.0.12/30 [110/144] via 10.0.0.5, 00:02:00, Serial0/0
O IA 10.100.100.2/32 [110/49] via 10.0.0.5, 00:02:00, Serial0/0
C 10.1.3.0/24 is directly connected, FastEthernet0/0
O 10.100.100.3/32 [110/97] via 10.0.0.5, 00:02:00, Serial0/0
O 10.1.2.0/24 [110/49] via 10.0.0.5, 00:02:00, Serial0/0
O IA 10.1.1.0/24 [110/97] via 10.0.0.5, 00:02:00, Serial0/0
O IA 10.0.0.0/30 [110/96] via 10.0.0.5, 00:02:00, Serial0/0
O IA 10.100.100.1/32 [110/97] via 10.0.0.5, 00:02:00, Serial0/0
O IA 10.100.100.6/32 [110/193] via 10.0.0.5, 00:01:34, Serial0/0
O IA 10.1.7.0/24 [110/193] via 10.0.0.5, 00:01:25, Serial0/0
O IA 10.100.100.7/32 [110/193] via 10.0.0.5, 00:01:10, Serial0/0
O IA 10.1.6.0/24 [110/193] via 10.0.0.5, 00:01:34, Serial0/0
C 10.100.100.4/32 is directly connected, Loopback0
O IA 10.1.5.0/24 [110/145] via 10.0.0.5, 00:01:29, Serial0/0
C 10.0.0.4/30 is directly connected, Serial0/0
O IA 10.100.100.5/32 [110/145] via 10.0.0.5, 00:02:00, Serial0/0
O 10.1.4.0/24 [110/97] via 10.0.0.5, 00:02:00, Serial0/0
O IA 10.0.0.16/30 [110/192] via 10.0.0.5, 00:01:29, Serial0/0
O IA 10.0.0.20/30 [110/192] via 10.0.0.5, 00:01:29, Serial0/0
R-DPS#sh ip ro
Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP
D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area
N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2
E1 - OSPF external type 1, E2 - OSPF external type 2
i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2
ia - IS-IS inter area, * - candidate default, U - per-user static route
o - ODR, P - periodic downloaded static route
Gateway of last resort is not set
10.0.0.0/8 is variably subnetted, 20 subnets, 3 masks
O 10.0.0.8/30 [110/96] via 10.0.0.5, 00:03:48, Serial0/0
O IA 10.0.0.12/30 [110/144] via 10.0.0.5, 00:03:48, Serial0/0
O IA 10.100.100.2/32 [110/49] via 10.0.0.5, 00:03:48, Serial0/0
C 10.1.3.0/24 is directly connected, FastEthernet0/0
O 10.100.100.3/32 [110/97] via 10.0.0.5, 00:03:48, Serial0/0
O 10.1.2.0/24 [110/49] via 10.0.0.5, 00:03:48, Serial0/0
O IA 10.1.1.0/24 [110/97] via 10.0.0.5, 00:03:48, Serial0/0
O IA 10.0.0.0/30 [110/96] via 10.0.0.5, 00:03:48, Serial0/0
O IA 10.100.100.1/32 [110/97] via 10.0.0.5, 00:03:48, Serial0/0
O IA 10.100.100.6/32 [110/193] via 10.0.0.5, 00:03:22, Serial0/0
O IA 10.1.7.0/24 [110/193] via 10.0.0.5, 00:03:13, Serial0/0
O IA 10.100.100.7/32 [110/193] via 10.0.0.5, 00:02:58, Serial0/0
O IA 10.1.6.0/24 [110/193] via 10.0.0.5, 00:03:22, Serial0/0
C 10.100.100.4/32 is directly connected, Loopback0
O IA 10.1.5.0/24 [110/145] via 10.0.0.5, 00:03:17, Serial0/0
C 10.0.0.4/30 is directly connected, Serial0/0
O IA 10.100.100.5/32 [110/145] via 10.0.0.5, 00:03:48, Serial0/0
O 10.1.4.0/24 [110/97] via 10.0.0.5, 00:03:48, Serial0/0
O IA 10.0.0.16/30 [110/192] via 10.0.0.5, 00:03:17, Serial0/0
O IA 10.0.0.20/30 [110/192] via 10.0.0.5, 00:03:17, Serial0/0
R-DPS#conf t
Enter configuration commands, one per line. End with CNTL/Z.
R-DPS(config)#router ospf 100
R-DPS(config-router)#end
R-DPS#conf t
*Mar 1 04:16:19.742: %SYS-5-CONFIG_I: Configured from console by vty1 (10.1.3.10)
R-DPS#wr mem
Building configuration...
[OK]
R-DPS#conf t
Enter configuration commands, one per line. End with CNTL/Z.
R-DPS(config)#int s
R-DPS(config)#int serial ?
<0-1> Serial interface number
R-DPS(config)#int serial 0/0
R-DPS(config-if)#ip o
R-DPS(config-if)#ip ospf aut
R-DPS(config-if)#ip ospf authentication
R-DPS(config-if)#ip os
R-DPS(config-if)#ip ospf au
R-DPS(config-if)#ip ospf authentication-k
R-DPS(config-if)#ip ospf authentication-key telkom
R-DPS(config-if)#ex
R-DPS(config)#sh
R-DPS(config)#sh ?
% Unrecognized command
R-DPS(config)#^Z
R-DPS#sh
*Mar 1 04:17:14.166: %SYS-5-CONFIG_I: Configured from console by vty1 (10.1.3.10)
R-DPS#sh ip
R-DPS#sh ip in
R-DPS#sh ip interface br
R-DPS#sh ip interface brief
Interface IP-Address OK? Method Status Protocol
FastEthernet0/0 10.1.3.1 YES manual up up
Serial0/0 10.0.0.6 YES manual up up
FastEthernet0/1 unassigned YES unset administratively down down
Loopback0 10.100.100.4 YES manual up up
R-DPS#
*Mar 1 04:17:24.002: %OSPF-5-ADJCHG: Process 100, Nbr 10.100.100.2 on Serial0/0 from FULL to DOWN, Neighbor Down: Dead timer expired
R-DPS#
*Mar 1 04:17:49.194: %OSPF-5-ADJCHG: Process 100, Nbr 10.100.100.2 on Serial0/0 from LOADING to FULL, Loading Done
R-DPS#debug ip ospf
R-DPS#debug ip ospf adJ
OSPF adjacency events debugging is on
R-DPS#TER
R-DPS#TERminal MO
R-DPS#TERminal MON
R-DPS#TERminal MONitor
R-DPS#debug ip ospf adj
OSPF adjacency events debugging is on
R-DPS#sh r
R-DPS#sh os
R-DPS#sh run | s router
router ospf 100
log-adjacency-changes
passive-interface FastEthernet0/0
network 10.0.0.6 0.0.0.0 area 1
network 10.1.3.1 0.0.0.0 area 1
network 10.100.100.4 0.0.0.0 area 1
R-DPS#
*Mar 1 04:22:04.130: OSPF: Rcv LS UPD from 10.100.100.2 on Serial0/0 length 56 LSA count 1
*Mar 1 04:22:04.346: OSPF: Rcv LS UPD from 10.100.100.2 on Serial0/0 length 56 LSA count 1
R-DPS#sh ip os
R-DPS#sh ip ospf ne
R-DPS#sh ip ospf neighbor
Neighbor ID Pri State Dead Time Address Interface
10.100.100.2 0 FULL/ - 00:00:39 10.0.0.5 Serial0/0
R-DPS#sh run in
R-DPS#sh run interface s0/0
Building configuration...
Current configuration : 187 bytes
!
interface Serial0/0
description ***To R-MDN***
bandwidth 2048
ip address 10.0.0.6 255.255.255.252
ip ospf authentication
ip ospf authentication-key telkom
clock rate 2000000
end
R-DPS#
Tidak ada komentar:
Posting Komentar